hogHog Hog Archives - Montgomery Industries

HH36

Typical applications include bark and the coarse reduction of solids such as yard trash or construction debris.

 

HH36 rings with individually pinned hammers provide a 36” cutting circle.

 

Rotor assembly incorporates two 3” X 23” steel flywheels for rotational momentum and to prevent material from binding against housing end plates.

 

Gravity discharge of material out of an opening in the base plate of the hog.

XL-KC

Typical applications include bark and wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 11” thick, as well as logs, lily pads, broken pallets and 60” whole pallets.

 

XL-KC removable lug rings have a 36” cutting circle.  The rotor has an inherently large rotational energy, so no flywheel is needed to process through momentary surge loads.

 

The rings can be hardsurfaced to extend their economic life in abrasive applications.

 

Gravity discharge of material out of an opening in the base plate of the hog.

CS-KC

Typical applications include bark and wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 9” thick, as well as logs, lily pads, broken pallets and 60” whole pallets.

 

CS-KC removable lug rings have a 32” cutting circle.  The rotor has an inherently large rotational energy, so no flywheel is needed to process through momentary surge loads.

 

The rings can be hardsurfaced to extend their economic life in abrasive applications.

 

Gravity discharge of material out of an opening in the base plate of the hog.

PM-KC

Typical applications include bark and wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 6” thick, as well as lily pads, broken pallets and 60” whole pallets. It can also be configured with special thin plate screens to process polyurethane and polymers.

 

PM-KC fixed lug rings have a 22” cutting circle and the rotor incorporates a 6” X 36” steel flywheel to process through momentary surge loads. The rings can be hardsurfaced to extend their economic life in abrasive applications.

 

Gravity discharge of material out of an opening in the base plate of the hog.

PM-HZF-BH

Typical applications include wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 5” thick.  Other applications include veneer roundup, plywood, and particleboard.

 

The PM series uses PM-GM rings with a 22” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

 

The horizontal feed is designed for the processing of long pieces using a vibrating conveyor.

 

Pieces larger than the hog can process in 5 to 10 seconds can be metered with an available Current Sensing Unit.

 

The discharge material can typically be conveyed up to 100 feet into a cyclone, truck, or open field using the #40, #50 or #60 Integral Fan.

PM-HZF, Rear Discharge

Typical applications include wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 5” thick.

 

Other applications include veneer roundup, plywood, and particleboard.

 

The PM series uses PM-GM rings with a 22” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

 

The horizontal feed is designed for the processing of long pieces using a vibrating conveyor.

 

Pieces larger than the hog can process in 5 to 10 seconds can be metered with an available Current Sensing Unit.

 

Rear discharge with a rectangular to round transition (included) allows pneumatic pickup of discharge material into an existing blowpipe system.

PM-HZF, Bottom Discharge

Typical applications include wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 5” thick.

 

Other applications include veneer roundup, plywood, and particleboard.

 

The PM series uses PM-GM rings with a 22” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

 

The horizontal feed is designed for the processing of long pieces using a vibrating conveyor.

 

Pieces larger than the hog can process in 5 to 10 seconds can be metered with an available Current Sensing Unit.

 

Gravity discharge of material out of an opening in the base plate of the hog.

PM-BH

Typical applications include bark and wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 5” thick.

 

Other applications include veneer roundup, polyurethane scrap, plywood, paper, gypsum, particleboard, broken and whole pallets.

 

The PM series uses PM-GM rings with a 22” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

 

The rings and fanwheel can be hardsurfaced to extend their economic life in abrasive applications.

 

The discharge material can typically be conveyed up to 100 feet into a cyclone, truck, or open field using the #40, #50 or #60 Integral Fan.

PM-ER

Typical applications include bark and wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 5” thick.

 

Other applications include veneer roundup, polyurethane scrap, plywood, paper, gypsum, particleboard, broken and whole pallets.

 

The PM series uses PM-GM rings with a 22” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

 

The rings can be hardsurfaced to extend their economic life in abrasive applications.

 

Gravity discharge of material out of an opening in the base plate of the hog.

BS-RC

Typical applications include bull screen rejects processing through a ½” or ¾” rectangular holed screen.

 

When the secondary grinding involves bull screen rejects in the harsh papermaking environment, the Montgomery Bull Screen Rechipper comes prepared for the job.

 

In addition to the aggressive cut and wear liners in the cutting chamber, the bearings are sealed, hose bibs are provided for flushing, stainless steel is welded to the rings and the housing is covered in a special anti-corrosion epoxy.

 

For the ultimate in corrosion resistance, the housing, wear liners, hardware, rings, teeth and screen can all be manufactured out of stainless steel.

HD-RC-BH

Typical applications include chips and shavings.

 

The rechipper is a modified HD hog with a more aggressive cut, hardsurfaced ring lugs and abrasion resistant wear lines in the cutting chamber.

 

The HD series uses HD-GM rings with an 18-3/4” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

 

The discharge material can typically be conveyed up to 100 feet into a cyclone, truck, or open field using the #40, #50 or #60 Integral Fan.

HD-RC

Typical applications include chips and shavings.

 

The rechipper is a modified HD hog with a more aggressive cut, hardsurfaced ring lugs and abrasion resistant wear lines in the cutting chamber.

 

The HD series uses HD-GM rings with an 18-3/4” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

 

Gravity discharge of material out of an opening in the base plate of the hog.

HD-HZF-BH

Typical applications include wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 3” thick.  Other applications include veneer roundup, plywood, and particleboard.

The HD series uses HD-GM rings with an 18-3/4” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

The horizontal feed is designed for the processing of long pieces using a vibrating conveyor.

Pieces larger than the hog can process in 5 to 10 seconds can be metered with an available Current Sensing Unit.

The discharge material can typically be conveyed up to 100 feet into a cyclone, truck, or open field using the #40 or #50 Integral Fan.

HD-HZF, Rear Discharge

Typical applications include wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 3” thick.  Other applications include veneer roundup, plywood, and particleboard.

 

The HD series uses HD-GM rings with an 18-3/4” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

 

The horizontal feed is designed for the processing of long pieces using a vibrating conveyor.

 

Pieces larger than the hog can process in 5 to 10 seconds can be metered with an available Current Sensing Unit.

 

Rear discharge with a rectangular to round transition (included) allows pneumatic pickup of discharge material into an existing blowpipe system.

HD-HZF, Bottom Discharge

Typical applications include wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 3” thick.

 

Other applications include veneer roundup, plywood, and particleboard.

 

The HD series uses HD-GM rings with an 18-3/4” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

 

The horizontal feed is designed for the processing of long pieces using a vibrating conveyor.

 

Pieces larger than the hog can process in 5 to 10 seconds can be metered with an available Current Sensing Unit.

 

Gravity discharge of material out of an opening in the base plate of the hog.

HD-BH

Typical applications include bark and wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 3” thick.

 

Other applications include veneer roundup, polyurethane scrap, plywood, paper, gypsum and particleboard.

 

The HD series uses HD-GM rings with an 18-3/4” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

 

The rings and fanwheel can be hardsurfaced to extend their economic life in abrasive applications.

 

The discharge material can typically be conveyed up to 100 feet into a cyclone, truck, or open field using the #40, #50 or #60 Integral Fan.

HD-ER

Typical applications include bark and wood scrap such as blocks, cutoffs, edgings, slabs and trim ends up to 4” thick.

 

Other applications include veneer roundup, polyurethane scrap, plywood, paper, gypsum and particleboard.

 

The HD series uses HD-GM rings with an 18-3/4” cutting circle and a steel flywheel for stored rotational energy to power through momentary surge loads.

 

The rings can be hardsurfaced to extend their economic life in abrasive applications.

 

Gravity discharge of material out of an opening in the base plate of the hog.

FS-HZF-BH

Typical applications include light wood scrap such as thin edgings, rippings and trim ends up to 1” thick with an occasional 2X4.

 

The FS series incorporates the punch and die design, internal shear pin protection and rugged construction of a Montgomery Hog.

 

The horizontal feed is designed for the processing of long pieces using a vibrating conveyor.

 

Pieces larger than the hog can process in 5 to 10 seconds can be metered with an available Current Sensing Unit.

 

The discharge material can typically be conveyed up to 100 feet into a cyclone, truck, or open field using the #30 Integral Fan.

FS-HZF, Rear Discharge

Typical applications include light wood scrap such as thin edgings, rippings and trim ends up to 1” thick with an occasional 2X4.

 

The FS series incorporates the punch and die design, internal shear pin protection and rugged construction of a Montgomery Hog.

 

The horizontal feed is designed for the processing of long pieces using a vibrating conveyor.

 

Pieces larger than the hog can process in 5 to 10 seconds can be metered with an available Current Sensing Unit.

 

Rear discharge with a rectangular to round transition (included) allows pneumatic pickup of discharge material into an existing blowpipe system.

FS-HZF, Bottom Discharge

Typical applications include light wood scrap such as thin edgings, rippings and trim ends up to 1” thick with an occasional 2X4.

 

The FS series incorporates the punch and die design, internal shear pin protection and rugged construction of a Montgomery Hog.

 

The horizontal feed is designed for the processing of long pieces using a vibrating conveyor.

 

Pieces larger than the hog can process in 5 to 10 seconds can be metered with an available Current Sensing Unit.

 

Gravity discharge of material out of an opening in the base plate of the hog.

FS-BH

Typical applications include light wood scrap such as thin edgings, rippings and trim ends up to 1” thick with an occasional 2X4.

 

The FS series incorporates the punch and die design, internal shear pin protection and rugged construction of a Montgomery Hog.

 

The discharge material can typically be conveyed up to 100 feet into a cyclone, truck, or open field using the #30 Integral Fan.

FS-ER

Typical applications include light wood scrap such as thin edgings, rippings and trim ends up to 1” thick with an occasional 2X4.

 

The FS series incorporates the punch and die design, internal shear pin protection and rugged construction of a Montgomery Hog.

 

The FS Series uses standard HD-GM rings but the rotor uses smaller bearings and does not include a flywheel.

 

Gravity discharge of material through an opening in the base plate of the hog.